Home » Howto

How To Build A Swing Out Garage Door

How to build a swing garage door

How To Build A Swing Out Garage Door 4.841808 out of 5 based on 177 ratings.

Related Videos »

  • Wooden Garage Door Makers

    Wooden Garage Door Makers

    Fitting Longham style Garage Doors by Handmade to measure in our workshop based in Poole Dorset, fitted locally or supplied as a complete kite including frames throughout the Mainland 01202 670

    Continue reading »

  • How To Build A Board And Batten Door

    How To Build A Board And Batten Door

    Carpenter and builder Rob Robillard from talks How To Build A Board and Batten Rob's website where he shares his industry training and experience to provide solutions to your problems and to make appropriate PRO recommendations for purchasing products, tools

    Continue reading »

  • Making Barn Doors For The Shed

    Making Barn Doors For The Shed

    Making a set of large "barn doors" for the front of the If it was a little deeper, I'd be able to park my car

    Continue reading »

  •  
  • A Wood One Piece Garage Door

    A Wood One Piece Garage Door

    This video is about 1pc Wood Door built from scratch start to finish to show you how much effort and work goes into a project like top and bottom rails cut to 15'11" *11-2x3x8 stringers cut to 6'9" *Frame nailed with 20p Galv nails *4 sheets of 4x8 3/8 rs ply with another two sheets ripped for tube of white painters caulking, used to seal all seams from water soaking in behind the design and rotting out the is what happened to the old bottom seal, we were gonna seal the sides as well but changed our drive saw *Chop saw *Router *Staple gun and 1 1/4 inch Estwing (no waffle head) *6-16p nails

    Continue reading »

  • Wooden Roll Up Door And Hinge Making * #5 ...

    Wooden Roll Up Door And Hinge Making * #5 ...

    Hinges handmade from old nails and a Railroad Tie handle all helping the wooden roll up garage Pallets Video_ from FREE pallets part

    Continue reading »

  • Hangar Style Bifold Door On My Shed 2

    Hangar Style Bifold Door On My Shed 2

    Due to the surprising interest in my shed door project, I thought I would post further Here is the link to the first video not very much detail since there was no plan to start with - it just sort of came points are that the halves of the door are equal length (height?) from the upper hinges to the middle and then from the middle to the rollers at the This equal length keeps the middle from flopping down when The view of the inside lower corners show the short bits of square tubing that keep the bottom edge of the door in place

    Continue reading »

  •  
  • Hanger Style Bifold Door On My Shed 1

    Hanger Style Bifold Door On My Shed 1

    This design was the best compromise that opened full height, took no internal ceiling space, allowed stuff to be stacked beside the opening both inside and out and can be opened with an obstruction just outside the The counterweight weighs about It is scrap lead pipe melted into a 4 litre paint The best part is that it cost a fraction of what a manufactured door would have is a second video showing

    Continue reading »

  • Building The Woodshop

    Building The Woodshop

    This is about how I built my wood We decided to move from our previous home for a variety of I saw the move as an opportunity to gain a bigger shop for my wood working The house we found had everything we wanted, except for a shop or even a It did have a non functioning indoor We thought this space would make a nice wood I could just build a floor over the pool and have a As we got further into the inspection process, it was looking as though fixing the structure over the pool was going to be It looked like we would have to put a bunch of money into a structure that was not really a

    Continue reading »

  • How To_ Build A Door

    How To_ Build A Door

    Bob Vila and carpenter Bob Ryley demonstrate how to build a wood For more how to's,

    Continue reading »

  •